Mastering Basic Plumbing for Installing a Bathtub
Mastering Basic Plumbing for Installing a Bathtub
Blog Article
How do you really feel about How to Install a Bathtub?
![Installing A Bathtub](https://www.myjobquote.co.uk/assets/img/cost-of-installing-a-new-bath-1.jpg)
Mounting a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately difficult project. If the old tub is readily accessible, the project can move easily; if you need to open a wall surface to get rid of the old tub and place the new bath tub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and embeded in the new one. Make sure you have actually certified yourself for the work and fit attempting it. As opposed to hiring a specialist to take over a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you might need a specialist plumber to make tube links.
This short article will certainly aid you set up a brand-new tub in your bathroom if you have actually already acquired a new bathtub and also do not need to transform the plan of your previous supply of water pipelines.
Your tools as well as material checklist must consist of the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent strain on the tub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you should do is separate the water. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted gain access to that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the staying water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required position. The wood boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression join; then do the very same for the other tap.
Activate the water supply and also examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow outlet and the normal electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the producer's instruction manual. Tiling and sealing around the bath tub must wait until the bath tub has actually been made use of a minimum of when as this will settle it into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Secure the tap in position with the supplier provided backnut. Once the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall surface between the bathroom and the tiling, leading to complications with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub is in usage. The sealer can fracture rather early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
![Installing A Bathtub](https://www.berkeys.com/wp-content/uploads/2016/12/Bathtub-Installation.jpg)
I am just very fascinated with Installing A Bathtub and I'm hoping you appreciated the entire post. Are you aware of anybody else who is in the market for the topic? Be sure promote it. Many thanks for taking the time to read it.
Go Company Report this page